Rolling shutter door remote control everyone must know, this kind of door is usually in the parking garage or the outside door of the store, but in the installation of this kind of door, there is a very important point, and many people are not very clear, must carry out the matching to use, today to follow the small make-up to understand these specific content.

常用的幾種卷簾門遙控器匹配方式

Several matching modes of remote control for rolling shutter door

種、車庫門遙控器:點按S鍵，2秒后顯示器右下方指示燈亮，按控制器任意鍵三次，小圓點指示燈忽明忽暗后對碼取得成功。一些透明控制器可以正確對碼可是沒法一切正常使用，這是必須將接收控制通道轉化， 有些透明遙控器通道轉化具體步驟如下:點按P直顯示5.再按2次＋號，隨后按著P不放手直返回到0，這時可以一切正常使用。

First, garage door remote control: press the s key, 2 seconds later, the indicator light at the bottom right of the display is on, press any key of the controller three times, the small round dot indicator light turns on and off, and then the code matching is successful. Some transparent controllers can correctly code, but they can't work normally. This is to convert the receiving control channel. For some transparent remote control channels, the specific steps are as follows: click P until the display is 5. Press the + sign twice, and then press P until it returns to 0. Then everything can be used normally.

第二種、車庫門遙控器:車庫門遙控器是滾碼的，電動機后有個紅色功能鍵，按一下下開展學習。按電動機上P鍵當出后按再按遙控器任意鍵，按哪個鍵，哪個鍵有用.出現閃2次表明對碼取得成功.再按添加控制器，按以上反復，完后功能鍵確認。

Second, garage door remote control: garage door remote control is rolling code, there is a red function key behind the motor, click to carry out learning. Press the p key on the motor. When it is out, press any key on the remote control again. Press which key is useful. If it flashes twice, the code matching is successful. Then press add controller, press the above repeatedly, and the function key will confirm.

                                          

第三種、車庫門遙控器:車庫門電機控制器有固定碼和學習碼二種，學習碼的是電動機主板接口遠離無線天線的那個按鍵，按一下下它，再按控制器的鍵，等候幾秒鐘及可;要是是固定碼的需用電鉻鐵電焊焊接，只有找技術的師傅來配了。

Third, garage door remote control: garage door motor controller has two kinds of fixed code and learning code. Learning code is the key that the motor motherboard interface is far away from the wireless antenna. Press it once, and then press the controller key, and wait for a few seconds. If it is a fixed code, it needs to be welded with electric chromium iron, only find a professional master to match.

第四種、車庫門遙控器:按一下下操作面板上的紅色按鈕，燈亮，隨后按一下下遙控器發射器的想要使用的按鍵就滅，再按一下下遙控器發射器的同一按鍵，燈經幾回忽明忽暗后亮起，遙控器發射器此按鍵學習取得成功，這時此按鍵可以開展對門體的實際操作了。如想再次學習遙控器發射器其他按鍵，請反復上述方法步驟;要是要增加發射器，也請按以上方法步驟開展反復學習，較多可學習25只發射器。要是亮1秒后就滅，則該發射器學習不成功，需再次開展學習。

Fourth, garage door remote control: press the red button on the operation panel, the light will be on, and then press the button of the remote control transmitter that you want to use, and then press the same button of the remote control transmitter, the light will turn on after several times of flickering, and the remote control transmitter will learn this button successfully. At this time, this button can carry out the actual operation of the door. If you want to learn the other keys of the remote control transmitter again, please repeat the above steps; if you want to add transmitters, please follow the above steps to carry out repeated learning. You can learn more than 25 transmitters. If it turns off after 1 second, the transmitter fails to learn and needs to learn again.